Newsgroup:
uk.rec.models.engineering
Add New Display Options
16
replies
Anybody here?
started 2021-02-10 22:14:03 UTC
2021-02-14 03:40:38 UTC
RustyHinge
1
reply
Craftsman Twin Model Engine
started 2021-01-02 01:18:02 UTC
2021-01-02 16:13:19 UTC
Clifford Coggin
1
reply
Any recommendations for an edge finder?
started 2020-11-06 16:53:51 UTC
2020-11-09 16:23:20 UTC
Brian Selby
4
replies
Case harden 316l?
started 2020-03-05 05:08:15 UTC
2020-10-26 02:17:53 UTC
Richard Smith
2
replies
Name a screw type
started 2020-10-21 22:17:44 UTC
2020-10-24 01:02:24 UTC
Peter Fairbrother
5
replies
Colchester Lathe forum
started 2018-03-27 03:31:26 UTC
2020-10-07 05:43:36 UTC
pmailkeey
2
replies
£300 MIG welder
started 2020-09-22 21:04:39 UTC
2020-09-23 01:49:03 UTC
Peter Fairbrother
1
reply
stub drill set?
started 2020-06-29 17:03:04 UTC
2020-09-22 21:50:37 UTC
n***@aolbin.com
2
replies
Moving Centec 2a?
started 2020-07-27 07:05:42 UTC
2020-07-27 15:09:39 UTC
Alan Dawes
3
replies
Flat filing
started 2020-06-29 17:00:42 UTC
2020-06-30 00:10:41 UTC
David Billington
1
reply
Gauge fitting
started 2020-06-16 15:30:26 UTC
2020-06-16 21:23:46 UTC
Clifford Coggin
14
replies
Limit/position switches
started 2020-05-24 02:16:36 UTC
2020-05-27 05:22:04 UTC
David Billington
2
replies
BSP Taper threads
started 2020-05-19 13:28:19 UTC
2020-05-24 02:14:45 UTC
Peter Fairbrother
9
replies
Qualters and Smith
started 2006-01-23 14:19:44 UTC
2020-05-17 23:31:21 UTC
d***@gmail.com
5
replies
Identify a thread
started 2020-05-12 22:41:43 UTC
2020-05-17 03:17:22 UTC
mick
5
replies
Death throes
started 2019-12-18 15:29:21 UTC
2020-05-12 22:45:33 UTC
rick
7
replies
Multitool Chucks- Lidl Parkside
started 2019-12-21 17:20:10 UTC
2020-03-06 00:32:03 UTC
Jim Wilkins
4
replies
Where to buy a good screw cutting lathe?
started 2020-01-06 04:53:06 UTC
2020-01-06 19:37:26 UTC
n***@aolbin.com
23
replies
"The Modern Pneumatic Airgun" by H.M. Buckley
started 2007-11-07 03:05:15 UTC
2020-01-01 19:01:01 UTC
Areligious Republican
10
replies
tube / pipe fit over scaffold tube
started 2019-11-08 00:20:39 UTC
2019-11-09 20:35:08 UTC
Jim Wilkins
2
replies
Name for lozenge head screws
started 2019-07-28 06:02:10 UTC
2019-07-31 04:23:35 UTC
David Billington
2
replies
Waste Suds
started 2019-03-18 23:09:15 UTC
2019-03-19 19:47:44 UTC
The Other Mike
2
replies
Compressors- leaving under pressure?
started 2019-03-17 19:51:22 UTC
2019-03-18 02:23:00 UTC
Brian Reay
4
replies
Thread Naming / Designation
started 2019-03-11 15:36:31 UTC
2019-03-14 08:01:02 UTC
pyotr filipivich
16
replies
Where to get brass BSW screws?
started 2019-02-21 20:09:58 UTC
2019-02-25 20:11:16 UTC
n***@aolbin.com
1
reply
Paint for cast iron gutters - Hammerite smooth?
started 2019-02-25 15:30:24 UTC
2019-02-25 15:31:06 UTC
n***@aolbin.com
14
replies
Flamefast DS230 Ceramic Chip Forge
started 2004-05-27 16:11:15 UTC
2019-01-26 21:48:01 UTC
Andrew Mawson
1
reply
soft vice jaws
started 2019-01-11 18:54:08 UTC
2019-01-12 05:44:52 UTC
Brian Reay
10
replies
Metric thread on an ML7
started 2017-08-15 16:29:36 UTC
2019-01-06 22:45:55 UTC
Dragon
6
replies
Is there a special name for...
started 2018-12-05 14:11:11 UTC
2018-12-08 04:20:24 UTC
Brian Reay
Click to Load More...
Loading...